Country Selection

Cartel Triple NEO Shafts

The Cartel Triple Neo aluminium / carbon shaft provides outstanding performance for all levels of archer, not just the elite professionals. Together with high quality but moderately priced arrow components you get a world beating arrow at highly sensible prices.

As a straight type aluminium / carbon arrow shaft the Triple NEO features a core produced from 7075 pure grade aluminium wound with an outer layer of high density U/D carbon. The aluminium tube provides superior resistance to crushing, bending and splitting. The Triple NEO is produced to be as thin and light as possible to provide maximum performance, durability and minimum wind drift. Finished with fresh and modern graphics. Set of 12 shafts only. Accepts all existing Cartel Triple components.

• Type: Parallel aluminium/carbon shaft
• Material: 7075 aluminium with high density carbon
• Straightness: ±0.001in
• Weight tolerance: ±1.5 grain

Sizes:

• 300
• 400
• 500
• 600
• 700
• 800
• 900
• 1000
• 1100
• 1200

Accessories:

• Points: Cartel Triple Point
• Pin: Cartel Triple Pin
• Pin Nock: Cartel Triple Pin Nock or any industry standard pin nock
• Insert Nock: Beiter 3.98 sizes 1, 2, H will fit Triple 300-700
• Outsert Nock: Cartel Triple Nock or selected Beiter nock options

Cartel Triple shafts are supplied without components. All points, nocks, pins, vanes must be purchased separately. For full details regarding accessories see below.

Technical:

This table shows the size, outside diameter, default factory uncut length, straightness tolerance and mass weight in grains per inch for each of the Triple Carbon-Aluminium shaft sizes.

Measuring the Spine: For the Triple range of arrows, the spine is determined as the weight required to deflect the shaft by 20mm with the shaft supported at points 500mm apart.

Selection Chart:

The following chart displays the recommended Cartel Triple shaft size selections suitable for target, field and 3D disciplines.

All Cartel Triple size selections should be made using the official selection chart shown above. All size selection charts act as a guide only and it is not an exact science. We cannot guarantee our recommendations, but we do have many years proven experience in advising and selecting sizes for world class archers. We are aware that certain computer software programs designed to make selections for you have proved to give very inaccurate results for these particular shafts.

DISCLAIMER: Neither Doo Sung Corporporation (Cartel Archery) nor Alternative Services will accept any responsibility for any incorrect selections made using the above chart.

Accessories:

Cartel Triple Points

Cartel Triple points are a break off type point. All models and sizes have two 10gn (approx) break off sections, although you can cut the shaft down smaller if you wish.

All points marked NEW are a stainless steel one-piece break-off point developed in close conjunction between Doo Sung Corporation (Cartel Archery) and Alternative Services. These points have been produced to feature a minimal external section and give the optimum performance for competitive archery.

Cartel Triple Pins

Cartel now produce a high quality nock pin system for their world beating range of Triple arrow shafts. Cartel Triple Pins are available in store in specific sizes to suit 300, 400, 500, 600, 700, 800, 900, 1000, 1100 and 1200 size shafts. Sold in packs of 12.

Accepts all industry standard pin nocks including Cartel Triple Pin Nocks, Carbon Tech McKinney Pin nocks, Bohning Blazer Pin Nocks, Bohning Smooth Release Pin Nocks, Beiter Pin Nocks (all sizes), Easton Pin Nocks, Easton G Pin Nocks, Fivics Soma Pin Nocks, Gold Tip Pin Nocks and Gold Tip HD Pin Nocks.

Cartel Triple Pin Nocks

To complement the high quality nock pin system for their world beating range of Triple arrow shafts, Cartel now also have a stylish new pin nock. Cartel Triple Nocks are available in large groove size in four colours and small groove size in orange and red colours to suit all Cartel Triple Pin sizes. Sold in packs of 12. Weight 2.9 grains

Colours:

• Blue
• Green
• Orange
• Red

Beiter 3.98 Insert Nocks

The Beiter 3.98 nock is a direct insert fitting nock and will fit the Cartel Triple 300-700 sizes without needing any other components.

These nocks are now produced in size 1, size 2 and HUNTER groove models but only in heavy colours. Beiter nocks are perhaps the best known manufacturers of nocks on the planet. Their selection is vast. The number of colour options is huge. The quality is unparalleled because all Beiter nocks of one size are manufactured in one single mould. This means you get the smallest tolerance between nocks!

Cartel Triple Nocks

The Cartel Triple nocks are a fit-over outsert type and are very similar to the popular old style X10 Outsert Nock. We stock the three main colour options; green, orange and red across the range of available spines - 300 to 1100. The nocks are available in small groove size only.

Colours:

• Green
• Orange
• Red

Beiter Outsert Nocks

For those looking for an outsert nock with a larger groove or if you have a particular preference for Beiter nocks then there are a number of options available.

• 300 - Beiter 5.7 + PTFE
• 400 - Beiter 5.48
• 500 - Beiter 5.4
• 600 - Beiter 2100
• 700 - no option
• 800 - Beiter 4.92 + PTFE or 1880
• 900 - Beiter 1880
• 1000 - Beiter 4.5
• 1100 - no option
• 1200 - no option

Triple 300 shafts will accept Beiter 5.7 outsert nocks with a little PTFE (plumbers tape) to provide a tighter fit.

Triple 800 shafts will accept either Beiter 4.92 outsert nocks with a little PTFE (plumbers tape) to provide a tighter fit or choose Beiter 1880 nocks and lightly rub down the arrow where the nock sits.